Home/Plumbing/Tap & Sink Installation
Plumbing · Taps & sinks
Tap and sink installation in Valencia — fitted right, sealed once, dripping never.
A tap is a hundred small chances to do it almost right. We fit taps, basins and sinks from €60 with new valves, correct torque and tested joints — the drip never gets its chance.
In plain terms
Small jobs deserve engineering too.
Nobody calls a plumber for a tap — until the flexi bursts on a Sunday. Every VELTORRA fitting gets new hoses and seals, its own shut-off checked, joints torqued rather than strangled, and a test under full pressure before we pack the tools.
Old one removed and disposed
Never re-used, always dated
Under full mains before we leave
For a straightforward swap
How it works
In and out, without encores.
Send a photo
Your tap or sink and the space under it — quote by message.
Visit
Old fitting removed, surfaces cleaned and checked.
Installation
New consumables, correct torque, sealed joints.
Test
Full-pressure check, hot and cold — then sign-off.
The price
Small job, exact price.
From €60 for a tap swap including new hoses and disposal of the old one. Basins, kitchen sinks and built-in fittings are quoted from your photo — before we drive.
- Removal and disposal of the old
- New hoses, seals and washers
- Shut-off valve check
- Sealed and torqued installation
- Full-pressure test
Why VELTORRA
What 'properly fitted' actually means.
New consumables always
Hoses, seals and washers replaced — not inherited.
Shut-off verified
The isolation valve tested, replaced if tired.
Correct torque
Tight enough to seal, loose enough to service.
Sealed interfaces
Sink rims and basin joints sealed against the slow creep.
Tested under pressure
Full mains, hot and cold, before sign-off.
The honest comparison
A professional fit against a hopeful one.
The tap is the same. The difference is everything that touches it — and what happens in year three.
Professional fit
- New rated hoses, dated and documented
- Isolation valve tested — or replaced
- Torqued to seal and to service
- Pressure-tested before sign-off
Hopeful fit
- The 2009 hoses — they held so far
- The valve that spins without closing
- Strangled threads, cracked ceramics
- Tested by the first night's drip
Service area · 39°28′N
The same standard at every address.
VELTORRA installs taps and sinks across Valencia, Torrent, Paterna, Burjassot, Mislata, L'Eliana, Godella, Rocafort, Alboraya and Sagunto — the same starting prices, the same documentation and the same lead engineer at every address.
Is this you
Worth a visit if…
A tap drips its little tax every night
The mixer wobbles on its base
Flexi hoses under the sink look aged
A new basin or sink waits in its box
The old tap seized — handle or cartridge
Water creeps around the sink rim
Related services
Plan the whole system, not one piece.
Questions, answered
Asked before hiring us.
How much does tap installation cost?
From €60 including removal of the old tap, new hoses and seals, and a full-pressure test. Send a photo of the fitting and the space below — you'll have the exact price by message.
Can you install a tap I bought myself?
Of course — most clients supply their own. We check compatibility from your photo first, so the visit is one visit.
My tap drips — repair or replace?
Cartridge swaps rescue good taps; cheap ones rarely deserve the part price. Send the model — we'll tell you honestly which side yours is on.
Do you install kitchen sinks and basins too?
Yes — undermount, inset and countertop, with traps and sealing done properly. Quoted from your photo before we come.
Why replace hoses if they look fine?
Flexi hoses fail from the inside, on a schedule nobody prints. New rated hoses cost a few euros; the ceiling below costs more. We replace them on principle.
Book the visit smaller than the puddle.
Send a few details — receive an itemised written estimate. No visits before you're ready, and no phone calls unless you ask for one.